K. Harris lab, Ctr for Learning and Memory, UT-Austin.

0.  Safety Precautions:

• You must complete required lab safety training before starting this procedure.
• If this is your first time doing this procedure, ask to be trained by an experienced lab member.  If you have not done this in a while, you should ask for a refresher.
• Before starting, even if you have done this procedure before,
  • read this protocol entirely
  • review relevant Safety Data Sheets and Harris Lab SOP (also see below)
  • ensure you have all reagents and supplies listed below
  • ensure all equipment is in good working order
  • have all waste containers ready (also see Clean-up)
  • plan your schedule well so that you wouldn’t have to rush
  • Review SDS and Harris Lab SOP for the following hazardous chemicals used in this procedure:
    • Ethanol: flammable; irritant (eye)
    • LX-112 epoxy resin kit
      • LX-112: irritation (eye, skin, respiratory, oral)
      • DDSA: irritant (eye, skin, respiratory)
      • NMA: irritant (eye, skin, respiratory)
      • DMP-30: permanent eye damage, irritant (skin, respiratory, oral)
• Osmium tetroxide: acutely toxic; mutagenic
• Potassium ferrocyanide: contact with acid releases very toxic gas
• Propylene oxide: flammable; acutely toxic (skin, respiratory, oral); serious eye damage; mutagen; carcinogen
• Sodium cacodylate: carcinogen; irritant (skin, eye); skin permeator
• Uranyl acetate: fatal (inhalation, ingestion); flammable
• Osmium tetroxide, propylene oxide, sodium cacodylate, and uranyl acetate must be handled only under a chemical fume hood.
• The following Personal Protective Equipment is required for this procedure:
  • Lab coat
  • Nitrile gloves (double-layer required; regularly check for holes)
  • Eye goggles
  • Also recommended: plastic apron and shoulder-length gloves
  • Place a piece of absorbent sheet on the work surface before starting the procedure.  When done, discard into the “Solid Waste – UA” bag
• Read the following papers:
  • Feinberg MD, Szumowski KM, Harris KM (2001) Microwave fixation of rat hippocampal slices. In: RT Giberson, RS DeMaree Jr. (eds.) Microwave Techniques and Protocols. Humana Press: Totowa, New Jersey. pp. 75-88. (PDF)
  • Jensen FE, Harris KM (1989) Preservation of neuronal ultrastructure in hippocampal slices using rapid microwave-enhanced fixation. J. Neurosci. Methods. 29:217-230. (PDF) 
  • Karnovsky MJ (1971) Use of ferrocyanide-reduced osmium tetroxide in electron microscopy. 11th annual meeting of the American Society for Cell Biology. New Orleans, Louisiana. (PDF)
  • Luft JH (1961) Improvements in epoxy resin embedding methods. J Biophys Biochem Cytol 9:409-414. (PDF)
  • Porter KR, Kallman F (1953) The properties and effects of osmium tetroxide as a tissue fixative with special reference to its use for electron microscopy. Exp Cell Res 4:127-141. (PDF)
    
  • White DL, Mazurkiewicz JE, Barnett RJ (1979) A chemical mechanism for tissue staining by osmium tetroxide-ferrocyanide mixtures. J Histochem Cytochem 27:1084-1091. (PDF)
    

1.  Setting Up

1.1.  Reagents and supplies (for up to 12 pieces of tissue):

• Vibraslices (70-100 µm thickness) of chemically fixed brain tissue, embedded into 7-9% agarose
• H₂O (purified water: double-distilled, ASTM type I, WFI grade, or equivalent; e.g., Fisher 91-502-5)
• 0.2M sodium cacodylate buffer (SCB; EMS 11652)
• 0.1M SCB (diluted from 0.2M SCB)
• Ethanol (EtOH; EMS 15056); use a fresh bottle for each processing.
• K₄Fe(CN)₆ · 3H₂O (potassium ferrocyanide, or KFeCN; Sigma P3289-100G)
• 2% uranyl acetate (UA; EMS 22400) in EtOH: See 2.4.1
  • Dissolve 1 g UA in 50ml EtOH, stored in dark at 4°C.
• 4% aqueous OsO₄ (osmium tetroxide; stored at 4°C; EMS 19190): See 2.4.2
  • Use a fresh ampule for each processing; discard excess
• Propylene oxide (PO; EMS 20411)
• Epoxy resin (LX-112 embedding kit; Ladd Research 21210)
• LX-112 (glycerol polyglycidyl ether; Ladd Research 21310)
• DDSA (dodecenyl succinic anhydride; Ladd Research 21340)
• NMA (nadic methyl anhydride; Ladd Research 21350)
• DMP-30 (2,4,6-tri[dimethylaminomethyl] phenol; Ladd Research 21370)
• Absorbent paper with plastic backing
• Disposable pipets (some with their tips trimmed – e.g., for LX-112 components, for transferring tissue)
• Kimwipes
• 12- or 6-well processing basket (Ted Pella 36157-1 or 36158-1) × 1 or 2.
  
  • These are stored in glass jars filled with acetone, in a fume hood.
• 50-mm polypropylene processing dishes (Ted Pella 36135) × 25 or 50.
• 20-ml syringes and syringe filters (PES membrane; 0.2-µm pore size) × 4 each.
• 20-ml borosilicate glass scintillation vials with caps (e.g., EMS 72634) × 10, labeled as below:
  
  • OsO₄
  • 1
  • 2
  • KFeCN
  • 50% EtOH
  • EtOH/UA: 1 each for 50%, 70%, 90%, 100%
  • 100% EtOH
• A Pasteur pipet and bulb, a 20-ml borosilicate glass scintillation vial without cap (labeled “OsO₄”)
• Ice packs: one for keeping OsO₄ solutions cold and another for cooling tissue during processing.
• Shell vials (EMS 72631-10 [3.4 ml]), 1 per tissue.
• Embedding mold (e.g., Chien mold, EMS 70140)
• Applicator sticks
• Razor blade
• Aluminum foil for preparing LX-112, as well as for wrapping open OsO₄ ampoule and used Pasteur pipet
• Tri-pour beakers:
  • 6 × 250-ml beakers for mixing LX-112 components (see 2.3)
  • 1 × 250-ml for collecting open OsO₄ ampoule and used Pasteur pipet
  • 1 × 250-ml for washing the processing basket in 0.1 M Na cacodylate buffer, and then for collecting liquid waste during the procedure (labeled “Waste cacodylate, osmium, UA-ethanol”).
  • 1 × 100-ml beaker for infiltration reagents (labeled “ethanol, propylene oxide, and LX-112”)
• Solid waste bags for UA and non-UA chemical-contaminated waste.Liquid waste bottles:
  • Formaldehyde, glutaraldehyde, and cacodylate
  • OsO₄, KFeCN, and cacodylate
  • Uranyl acetate, ethanol
  • Flammables
  • Resin and propylene oxide

2.  Reagent/Equipment Preparation (on the day of processing)

2.1.  Tissue processing bascket

• Remove and air-dry 12- or 6-well processing basket from acetone, then wash in a disposable beaker filled with SCB (0.1M, pH 7.4).

2.2.  Microwave

1. Fill load cooler with fresh deionized water and attach tubing to cold spot device.  Make sure pump is on.
2. Set microwave power level to 1 (175W).
3. Run microwave for 2 minutes to warm up magnetron.

2.3.  Epoxy resin (can be done the day before)

1. Place stir bars (kept in acetone) in three tri-pour beakers and label "A", "B", and "A+B".
2. Measure resin components with the scale in fume hood, using disposable pipettes with their tips cut off.  

• The recipe here should make enough resin for embedding up to 24 pieces of tissue.   
• The amounts of DDSA and NMA must be adjusted according to the weight per epoxide (WPE) of LX-112 (indicated on the bottle), so refer to Table 1 for their correct amount: 
• Beaker A: mix LX-112 and DDSA
• Beaker B: mix LX-112 and NMA

1.  Cover both beakers with aluminum foil and place on stir plates.  Mix for at least 15 min.  Do not mix too vigorously to avoid bubbles, just enough to have a slight vortex.
2. Into beaker A+B, add the contents of beakers A and B (see Table 3 for the amounts).  Cover with foil and mix for another 15 min.
3. Add DMP-30 (see Table 3 for the amount) and mix thoroughly for another 15 min.

2.4.  Reagents for osmium fixation, dehydration, and UA en bloc staining

2.4.1.  Handling sodium cacodylate buffer

**under construction**

2.4.2.  Stock solution of uranyl acetate, 2% in ethanol

**under construction**

2.4.3.  Handling osmium tetroxide

**under construction**

2.4.4.  Reagents for processing up to 12 pieces of tissue

• In 50-ml conical tubes, add:
  • ddH₂O: 50 ml
  • Na cacodylate buffer (SCB; 0.2M): 15 ml
  • Na cacodylate buffer (0.1M): 50 ml (~150 ml total will be needed)
  • In the labeled vials (Mix well by shaking):

              * See above (2.4.3) for how to dispense 4% OsO₄.

**Reduced osmium:

1. Add 3 ml of KFeCN solution to vial 2.
2. Place vials 1 and 2 on ice.
3. When ready, pour vials 1 and 2 back and forth to mix well before adding to tissue.

***1% OsO₄: Keep vial on ice until use.

2.4.5.  Reagents for processing up to 24 pieces of tissue

• In 50-ml conical tubes, add:
  • ddH₂O: 40 ml (additional 40 ml will be needed during processing)
  • Na cacodylate buffer (SCB; 0.2M): 20 ml
  • Na cacodylate buffer (0.1M): 50 ml (~300 ml total  will be needed)
  • In the labeled vials, prepare the following (Mix well by shaking):

              * See above (2.4.3) for how to dispense 4% OsO₄.

**Reduced osmium:

1. Add 5 ml of KFeCN solution to vial 2.
2. Place vials 1 and 2 on ice.
3. When ready, pour vials 1 and 2 back and forth to mix well before adding to tissue.

***1% OsO₄: Keep vial on ice until use.

2.5.  Reagents for infiltration

• Prepare ~2 ml per tissue of the following:
  • 1:1 = EtOH : propylene oxide (PO)
  • 1:2 = EtOH : PO
  • 100% PO
  • 1:1 = PO : Resin
  • 1:2 = PO : Resin

3.  Processing (2 days)

Day 1 (estimated work duration: 3 hrs + enough time for dissection and agarose embedding)

1. Place a piece of absorbent paper on work surface in the fume hood.
2. Prepare reagents and equipment, as described in Section 2 above.
3. Place 12- or 6-well processing basket in 50-mm processing dish filled with Na cacodylate buffer (SCB; 0.1M, pH 7.4).
4. With a disposable pipet, transfer the tissue (embedded in 7-9% agarose) to the processing basket.
5. SCB washes, 5 min × 5.
6. Osmium fixation/en bloc staining
   
   1. Reduced osmium (1% OsO₄ + 1.5% K₄Fe(CN)₆ in SCB), 5 min.
   2. Pour vials 1 and 2 back and forth to mix before adding to tissue.
   3. SCB washes, 5 min × 5.
   4. 1% OsO₄ in SCB, in microwave (175 W, or power level 1) under vacuum, 1 min on → 1 min off → 1 min on.
   5. Place on ice, cool to about 15°C.
   6. Repeat microwave under vacuum, as in Step 5.iii. above.
   7. SCB washes, 2 min × 5.
   8. H₂O washes, 2 min × 2.
7. Dehydration
   1. 50% EtOH, 5 min.
   2. Dehydration and en-bloc UA staining in microwave (250 W, or power level 2) without vacuum, 40 sec each.  UA-EtOH mixtures must be filtered through the syringe filter.
      1. 50% EtOH with 1% UA.
      2. 70% EtOH with 1% UA.
      3. 90% EtOH with 1% UA.
      4. 100% EtOH with 1% UA.
      5. 100% EtOH.
8. Infiltration on rotator.  With a disposable pipet (with the tip cut off), transfer the tissue into shell vials containing 1:1 = EtOH : PO.  After each exchange, make sure the tissue is not stuck on the bottom of vial.
   1. 1:1 = EtOH : PO, 10 min.
   2. 1:2 = EtOH : PO, 10 min.
   3. 100% PO, 15 min × 2.
   4. 1:1 = PO : Resin, 1 hr.
   5. 1:2 = PO : Resin, overnight.

Day 2 (estimated work duration: 4 hrs)

1. Make a fresh batch of resin (See 2.3.).
2. Infiltration with 100% Resin, 1hr × 3 on rotator.
3. Place block labels writing side up in embedding molds and cover with a small amount of fresh resin.
   • Suggested label format:
   1. • Font: Tw Cen MT Condensed, 9 pt., with 8 pt. spacing between lines
      • Width = 0.5 in. max; Height = 2 lines max
      • Label information should at least contain: Animal ID (e.g., MK01) and Tissue ID (e.g., R42CA1, for right hemisphere, vibrasection 42, area CA1)
4. Bevel a wooden applicator stick with a razor blade.  Using the stick, transfer the tissue from shell vials into the mold.
5. Under a stereomicroscope, move the tissue to desired position.
   
   • Small blocks of polymerized resin can be used to support the tissue inside the mold.
6. Make sure that the resin is slightly convex from top of the mold.
7. Polymerize resin for 48 hr at 60°C.

Day 3 (estimated work duration: 0-1 hr)

1. Continue resin polymerization.  You may check and adjust the positioning of tissue at this point.

Day 4 (estimated work duration: 1-2 hrs)

1. Take the resin-embedded tissue blocks out of oven.  Remove the blocks out of the mold immediately and store in the cardboard pill boxes labeled with block identification numbers. 
2. Take solidified resin waste into “Solid Resin” waste drum.
3. Examine the blocks under the stereomicroscope and record their images before trimming and cutting.
4. Scan worksheet into a pdf file.

4.  Clean-up

4.1.  Waste containers:

• Hazardous Liquid Waste: Pour all waste into the proper waste collection bottles available in fume hood.
  • Aldehyde-Cacodylate (fixative solution, cacodylate buffer)
  • Osmium-Ferrocyanide (reduced osmium/osmium tetroxide): Discard excess K₄Fe(CN)₆ and OsO₄.
  • Uranyl acetate-Ethanol (ethanolic UA solution)
  • Flammable Solvents (propylene oxide and alcohols that do NOT contain other chemicals such as uranyl acetate and Epon)
  • Resin-PO (mixture of LX-112 and propylene oxide)
    • One resin beaker should be used to collect all excess LX-112 resin and aluminum foil, plastic pipets, applicator sticks, and vials (uncapped) used with it.  This should be cured in the oven with the blocks and discarded in hazardous solid waste container labeled “solid LX-112 resin”.
• Hazardous Solid Waste: Place all contaminated solid waste (e.g., gloves, pipets, vials, processing dishes, etc.) into hazardous waste bags in fume hood.  All vials must be uncapped and empty.  Make sure to separate all waste contaminated with UA.

4.2.  Used supplies and equipment:

• Supplies (e.g., vials and dishes) that came in contact with UA should be rinsed with ethanol into the UA waste bottle and disposed of in the solid UA waste bag.  All vials must be uncapped and empty.  Make sure to separate all waste contaminated with UA.
• Used absorbent paper should be discarded into the UA solid waste bag.
• Wipe inside vacuum chamber of the microwave with wet Kimwipe (discard into the UA waste bag).
• Stir bars (for resin mixing) and processing baskets should be placed in jars of acetone in the fume hood.
• Monitor the area for radioactivity (see Harris lab SOP for uranyl acetate).