Page Comparison

...

You are 100% financially responsible for repair and/or replacement in the event of damage or loss of the Bolex as well as any other equipment checked out from RTF Checkout.

Reflex Viewfinder

The optical system of the Bolex H-16 reflex cameras utilizes a beam splitter permitting through the lens viewing at all times free from flicker. The reflex viewfinder enables accurate focusing and framing, and allows you to estimate the depth of field. The reflex prism deflects 20 - 25% of the light passing through the lens into the viewfinder system. Only 75 – 80% of the light reaches the film plane. The actual quality of the light reaching the film is reduced by about 1/2 to 1/3 of an f-stop. To compensate for the light reduction, Bolex has determined that the effective shutter speed for the H-16 camera is 1/80 of a second rather than the standard 1/65 of a second.

Another compensation for the light loss is the RX lens designed by Bolex with Kern/Switar..The RX lens is calibrated to pass 1/2 to 1/3 more light than the aperture markings on the barrel
indicates. When using RX lenses with the H-16 camera, the effective shutter speed is back to 1/65 of a second.
When using non-RX lenses of 50 mm or less, satisfactory results can be obtained when stopped down to f/8 or smaller.

Lenses

Six of our Bolex cameras, the SBMs, take Bayonnet mount lenses. The remaining cameras take CMount lenses. Refer to the chart Bolex Cameras and Their Attributes” on the RTF website to determine which lenses you can use on each Bolex camera. IF YOU ARE USING AN SBM BOLEX and you want to use CMount lenses, YOU MUST RESERVE A BAYONNET TO
CMOUNT ADAPTER. http://rtf.utexas.edu/equipment/bolex/PROD75_021106.html shows you the proper way to install the Bayonnet to CMount adapter. If you install it incorrectly, your
image will never be in focus.

Douser

The douser (located on the reflex viewfinder) closes the eyepiece to keep light from reaching and fogging the film plane through the viewfinder. The douser is open when the lever is in the
horizontal position and closed when in the vertical position. Close the douser whenever your eye is removed from the eyepiece to prevent film from fogging.
Douser in OPEN position

Diopter Adjustment

The diopter adjustment corrects the optical system to the operator’s eyesight and remains the same for all lenses on the camera. If you wear glasses, you can adjust the diopter to your eyesight and achieve accurate focus without your glasses. Always set the diopter to your eyesight [before filming].
To set the diopter:
1. Turn the turret to expose the reflex prism (no lens in the taking position) or remove the cover of the bayonet mount.
2. Point the camera at a light source.
3. Unlock the diopter adjustment either by loosening the grooved ring around the viewfinder or the locking screw depending on the camera model.
4. Adjust the viewfinder until the grain of the ground glass is perfectly sharp.
5. Lock the diopter finger tight, but do not over-tighten.

Turret

You can change from one lens to another by turning the turret. To turn the turret, use the fold away lever rather than handling the lenses so that you avoid accidentally changing the aperture and/or focus ring – or damaging the lenses and/or camera. When using heavier lenses, The turret lock is located above the lens in the taking position and should be tightened before the
lenses are in place. Place wide-angle lenses and the telephoto lenses opposite of each other on the turret so that the telephoto lens does not interfere with the field of the wide-angle lens. To attach a lens, simply unscrew the turret cap and screw on the lens. You can have up to three lenses mounted at once on the turret mount. If using less than three lenses, make sure turret caps are secured in unused positions. DO NOT LOSE TURRET CAPS.
*You may loosen or tighten the turret lock but never entirely remove it. Removing it leaves a hole that light can enter and expose your film.

Turret Mount Filters

Cameras with a turret mount have a filter between the taking lens position and the reflex prism. The filter remains in place no matter which lens is used. When filming without a filter, an empty filter carrier should be left in the filter slot to prevent light from entering the camera trough the slot and fogging the film. Make sure the carrier is located firmly within
the slot and the correct filter is in place before shooting. An incorrect filter will either alter the color balance or the exposure.

Bayonet Mount

The Bolex H-16 SBM camera has a single lens bayonet mount and is recommended for use with heavier lenses. To mount a lens:
1. Turn the outer ring in the direction of the arrow (counter-clockwise if camera is facing you). Press the button on the bottom of the mount to move the screw into the open
position where you will se the tabs of the cap.
2. Lift the cap out of the mount and immediately place the lens mount in its place. Be careful not to touch the prism!
3. Turn the ring clockwise to secure the lens mount in place and screw the lens into place.

To remove a lens and secure the bayonet mount:
4. Unscrew the lens; replace lens caps and return to lens case.
5. Turn outer ring as described above until tabs in lens ring are revealed.
6. To remove the lens mount, tip camera forward with hand cupped under below to catch the lens mount. DO NOT touch prism with fingers!
7. Replace cap and secure by turning lens clockwise.

Bayonet Mount Filters

Filter insertion is from the control side of the camera. When not in use, the filter should be left in the storage position with the lever folded down and locked. To insert a filter:
1. Slide the button down and insert the filter into the filter slot with the notched side down.
2. The first position is where the filter can be stored until needed. Fold the handle down and secure in notch. To use the filter, it must be inserted all the way in to the filter slot so that it is in between the lens and the prism.
3. From the storage position, unfold the lever. Slide the button down and continue inserting the filter until it’s all the way in.

Film Speeds

The camera has film speeds ranging from 12 to 64 frames per second, except for the H-16 Reflex (the earliest model) which also has a setting for 8fps. To select the desired film speed, Turn the control knob until the corresponding figure is opposite the red dot. When changing filming speeds, do not forget to alter exposure setting. (When changing from 24 to 48 by one stop and so forth.)

Release Selector (aka Side Release)

The H-16 can be used for normal, continuous or single frame filming. The different operations are controlled by the release selector.
- Normal – This method is suitable for most shooting situations. The camera runs as long as the operator depresses the front release button or pushes the release selector towards M.
- Continuous – Push the release selector towards M until it clicks into place. The camera will continue running until the wind runs out or the release selector is pushed back to the STOP position.
- Single frame – Use a cable release adapter to attach a cable release to the release selector. The adapter should be set so that the cable release pushes the release selector towards the P. Single frame exposures can be set for Instantaneous or Time Release. Turn the knob or lever to I to select Instantaneous. The effective shutter speed is 1/30 of a second. To select Time Release, set the knob’s guide mark or the lever to T. The shutter will stay open for as long as the release selector is set to P.

Camera Motor -Internal

The H-16 cameras have a spring drive motor. The motor can be disengaged to backwind the film.
To wind the camera:
1. Set the disengaging lever to MOT and the release selector to STOP. (If the release selector will not go to STOP, slightly wind the spring.)
2. Lift the winding crank, which automatically engages the spindle, and set so that the slot in the handle is secured on the tab.
3. Wind the spring counter-clockwise fully without forcing it.
4. Fold the crank back and secure it on the latch on the lower body. Fully wound, the motor will drive about 18 feet of film through the camera (about 28 seconds at 24fps). Important: Never leave the camera wound during storage. This may ruin the spring. When running down the camera with no film loaded, set the film speed at the lowest setting.

Camera Motor --External

Set your camera speed to 64 BEFORE you put the motor on or you may put drag on the motor. If you do not set the speed to 64, the governor on the camera will control the camera instead of the motor controlling it, and your speed will run too slow (because of the drag). Bolex motors can only fit on certain Bolex cameras. Refer to the chart called “Bolex Cameras and Their Attributes” on the RTF website First, make sure there's no wind on the spring motor. Remove the winding crank by putting it in the normal winding position and slowly "winding"
clockwise (opposite the way you normally wind it). Set the film speed to 64 fps, lock the trigger in the "M" position, and disengage the spring motor (put the "MOT/O" lever in the "O" position).
Set the camera on/off switch to the "M" position. Place the motor on the camera by matching up the screws. Tighten the screws lightly with a slotted screwdriver or coin. Carefully attach a charged 12V battery (e.g., Bescorp LCR) to the camera with the coiled cable provided.* Depress the silver button on the front of the motor. The camera should run at speed (24 fps), indicated by a constant white light on the back of the motor.
• Note: When detaching this cable from the motor, make sure you unscrew the cable all the way before removing it. In the past, people have tugged hard on the cable while it was partly screwed onto the motor, causing damage to the cable.
• Note: There is a very short cable attached to the motor. It has no function with our Bolex cameras, just leave it alone please.

Variable Shutter

The H-16 is equipped with a shutter capable of having its aperture varied whether or not the camera is running or stopped. This enables you to reduce exposure time without altering the camera running speed or f-stop. In bright light, the variable shutter can be used to reduce exposure, therefore eliminating the need for a neutral density filter. The shutter may be locked in each of its five positions by pulling it out and pushing in when at the desired setting. The markings on the variable shutter correspond to the equivalent f-stop change (i.e., filming at the 1/2 mark is equivalent to stopping down by 1/2, at mark 2 equals closing down the lens diaphragm by 2 stops.)
******When the variable shutter is fully closed, no light enters the film plane.
Warning: You can still see an image through the viewfinder if the variable shutter is closed. Some cameras show a triangular warning signal, but not all. Make sure you variable shutter is opened to the correct setting when filming or your film will NOT be exposed.

Footage Counter

The footage counter indicates how much film has been exposed. The counter will automatically reset when the lid is removed and will read FEET.

Frame Counter

The frame counter is helpful for lap dissolves, double exposures and animation. The frame counter adds frames in forward run and subtracts them in reverse. The upper dial counts single frames, 0 - 50. The lower dial totals in units of 50 frames, 0 - 1000.

Loading the Camera Image Modified

1 - Pressure Pad Locking Pin
2 & 10 - Loop Former
3 & 12 - Spool Shaft
4 - Loop Former Locking Lever and Opening Knob
5 - Audible Signal Click Lever
6 - Spool Ejector
7 - Spool Retaining Arm
8 - Sprockets
9 - Pressure Pad
11 - Film Knife

...

You can watch a video of how to load the Bolex

Lap Dissolve

Superimposing a fade-in on a fade-out makes a lap dissolve so that one picture gradually disappears as the next gradually appears. (This is also known as a cross-dissolve.) This allows for a smooth transition during which the picture brightness scarcely varies. To produce a lap dissolve:

1. Close the first shot in a sequence with a fade out. When beginning to close down the variable shutter, note what frame you are at in the frame counter. Alternatively, time how long
it takes you to reach the closed position from the start of the fade and stop filming.
2. Lock the variable shutter in the closed position.
3. Disengage the motor by setting the selector to 0.
4. Set the release selector to M.
5. Close the douser if not already closed by moving it into the vertical position.
6. Cap the lens.
7. Using the backwind key, rewind the film until the frame counter indicates the duration of the fade out.
8. Move the release selector to the STOP position.
9. Frame the second sequence to be filmed.
10. As you begin filming by pressing the release selector to M, begin the fade in by moving the variable shutter smoothly to the open position.
11. Lock the variable shutter into the open position.

Rex-o-fader

The Rex-o-fader is an accessory that can help with smooth fades and is available upon request.
.

Troubleshooting