Content Comparison

...

?????Not sure what we did here notes from other session back in 2017 here

We went to lower the Gamma to make it work better
Turned on Advanced Contrast Enhancer and LED Dynamic Control
Look at the Moving Stripe pattern you want to see the display look darker.
This turns on Local Area Dimming

You will need the Dell Laptop with the Calman Software installed and the Klien Colorimeter and the Murido signal generator	This is stored in a case in the back of the helpdesk in CMA 3.104
Turn on Monitor so it warms up
Connect Murideo signal generator via USB to laptop. Make sure the Murideo drivers are installed http://www.murideo.com/downloads.html
Plug in the HDMI out of the Murideo Signal Generator output to the TV you want to calibrate MAKE SURE IN USE HDMI 1 WHERE THE BLACKMAGIC I/O IS PLUGGED Set the LG TV HDMI input to the input from the Murideo HDMI INPUT 1
Press the red ON button on the Murideo
Now you should see the images from the Murideo on the TV
Murideo Signal Generator connected via USB - Use USB to Serial Port 4 on Laptop for the Murido Signal Generator
On the Klien Camera remove the lens cap
and put on the Lens Hood on the Klien camera
Put the Klien on a tripod Pull up the Murido slide that shows the target as this example *Put the cup smushed up to the TV so rubber is blocking out all the light completely flush to the monitor*
Another example of the camera pressed up against the monitor
Connect the Klein Colorimeter via USB into the computer
Log into laptop	with UN comm - xxxxx and password
Open Calman software on the laptop using the desktop shortcut
Enter in the details and click Start Session Client – Default Calibrator – your name Display System put in as much info as possible (Sony TriMaster ex:) Display Model is PVMX-550 Remember under Workflow choose ISF Calibration Choose Start Session
Hit Next Here
Setup the meter position Remember place the Colorimeter up against the monitor Click Next
Skip the Pre-Calibration Settings - Click Next
On the LG Remote click the Gear Icon and then use the down arrow to get to All Settings
Set the TV to Picture Mode isf Expert (Dark Room)
Turn off the lights in the room put in the CC environment Also put something on the computer monitor "Resolve"
Do the Pre - Calibration View and Read Series to get an idea how the Monitor Looks ISF Dark is pretty good Click Next
Mode Settings put the LG in BT.1886 On the LG Remote LG Remote > Gear Icon > All Settings > Advanced Settings >Brightness>Gamma > Leave at BT.1886
In Gamma BT.1886 it is the closest to the Gamma Target Line Press Read Series or "Goal Post" Then Press Next	PICTURE here
White Point and Color Space
LG Remote > Star > All Settings > Advanced Settings > Color > White Balance
To set the White Point Select the White selector block
Then Click on the "Infinity button" and while it is running toggle through all the color temp settings that the TV has
Press and hold the Color Temp slider but Warm 50 is the best = default the dot is right in the white box
Now we need to set the right Color Space
LG Remote > Star > All Settings > Advanced Settings > Color . Color Gamut and leave it at Auto
Turn off all Auto Features No automatic adjustments should be on Clarity All off and TruMotion is off Real Cinema Off
LG Remote > Star > All Settings > Advanced Settings > Brightness > Auto Dynamic is off and >Peak brightness off and >Video Range Not Auto - Do limited >Motion Eye Care Off	FG here
LG Remote > Star > All Settings > Advanced Settings > Color > Color Gamut = Auto Fine Tune Color Adjustment make sure it is also off	FG Here
LG Remote > Star > All Settings > Advanced Settings > Clarity > All off	FG HereAdjust Luminance
Once Everything is off click Next	Image Added
Adjust Luminance Click on Read Continuous lower left corner	Image Removed
LG Remote > Star > All Settings > Advanced Settings > Brightness and adjust the Backlight or on the LG the Contrast settingOn the LG Remote click the Gear Icon and then use the down arrow to get to All Settings ISF Dark >Contrast PICUTE HERE Image Removed adjust the Backlight setting - Sony TriMaster doesn't have this on the TV our example we set it to max and according to the specs we should be Get the LG to about Contrast at 86 or 30-40 FL	Picture on the phone		30-40 for a dark room Image Added
Here are the specs 40 to 50 for a Dim Room our suites these are the specs for the rooms that we want to follow
Note 4.112 Suite K contrast is set to 100 for a Dim Room Had a Peak White Luminance set to 43.2 fl	FG Here
Click Next	Image Added
Next click on the Dynamic Range Click on Brightness button and set so that the Dynamic Range to check this click on Read Series
This is the result of the Read
Not Bad but can adjust Press these buttons Brightness and Contrast Press Brightness button
Press Black Level not Brightness set black level to 58 Press Brightness and will get the controls to adjust for the Black PLUGE test pattern –LG Remote > Star > All Settings > Advanced Settings > Brightness > Black Level You want to barely see 16 and 17 but should not see any squares below 16 those should be invisible. Image Removed We set Black Level to 58-60 on the LG Monitors	Image Added
Press Contrast Menu in Calman Software -
to put up the White Pludge you want to see up to 254 and don't want to see any pink tones or noise? LG Remote > Star > All Settings > Advanced Settings > Brightness > Use Adjust Contrast on the LG to adjust this 82 seemed the best	Image Removed	Change the 2.4 to 2.6 and others but 2.4 usually is the best	Image RemovedImage Added
Once Brightness and Contrast are set Click Next	Image Added
Gamma Settings control	Image Removed
Press the "Goal Post" again to take a reading of the Gamma Settings	Image Removed
Make sure the White Line is Close to the Yellow Line - less expensive TV's you will see fall off in the Low areas	Image Removed
Image Removed	?????Not sure what we did here notes from other session back in 2017 here We ended up turning on Local Area Dimming by turning on LED Dynamic Control Optimizes contrast by adjusting brightness in individual sections of the screen Gamma also was changed to -2 this is a repeat of Gamma on step 2 but this is a 10 point control instead of a 2point control. Click On NextLG Remote > Star > All Settings > Advanced Settings > Color > Color Gamut = Auto Auto looks the best so just leave on Auto	Image Added
Click Next	Image Added
Color Decoder - Skip this Step on the Sony Trinitron in Grad Suite H	Image Removed
This Sony 65 does not have blue only mode. But click on Color and Tint to see the Color Bars on the Monitor if the TV has that	Image Removed
Turn the "Color and Tint" settings to get these to stripes like this	Image Removedthe LG's and Sonys don't have this	Image Added
Click on Next	Image Added
Resolution/Bit-Accuracy
You can click on the test patterns here
Pull up ISF Geometry to check for OverScan Check for the white lines at the edges to make sure you are seeing everything - Not a crucial step so it's Optional LG Remote > Star > All Settings > Advanced Settings >. Aspect Ratio 16:9 Turn on JUST SCAN
Click Next!
Greyscale Two Point Adjust
Select 80 Percent White Click on the 80 percent button	Image Modified
Click on the Continuous read button	Image Modified
You will go to your White Balance settings to find your RGB Gain and Bias You will control the RED Green and Blue Gain=High controls

...

LG Remote > Star > All Settings > Advanced Settings > Color >White Balance

RGB balance

RED = +2

Blue = -3

You want to adjust the Red Green and Blue controls until you get all 3 RGB colors to match exactly this is close but not exact

...

This is what we ended up

...

with

...

Image Added
Then we clicked on 30 %	Image Modified
Click on the Continuous read button	Image Modified
Repeat the same process for the 30 percent chip LG Remote > Star > All Settings > Advanced Settings > Color >White Balance RGB balance RED = +2 Blue = -3 You want to adjust the

...

Red Green and Blue controls until you get all 3

...

RGB colors to match exactly this is close but not exact

Sony you'll use these menus and knobs

Image Removed

...

This is what we ended up

...

Image Removed

Frame grab of CIE X and Y get a picture to insert here

with

Toggle back and forth with the 80 and 30 toggle till you get the Bias's and Gains to be absolutely flat

Picture here

Image Added

Finally after you are finished do a Goal Post "Read Series" to get the final reading to make sure all's good.

Image Modified

...

Click NEXT

OLED LG has this but we'll skip this on the Sony Trinitron

You can take a "Read Series" click on Goal Post

Image Removed

Object is to get All the Deltas under 5 is exceptable

Get the X to read .312 and the y .to read 329

Image Removed


Final reading delta E should be below 1	FG or two point here
click Next	Image Added
Grayscale and Gamma Multipoint Adjust	Image Added
LG Remote > Star > All Settings > Advanced Settings > Color > White Balance > Method > Change to 10 Points	Image Added
Click on Read Series "Goal Post"	Image Added
LG Remote > Star > All Settings > Advanced Settings > Color > White Balance > Signal Level % and this is where we'll change the signal level of the TV from 10 to 100 percent to match the chip on the calman software

You would have to adjust the RGB on every point if you have that on your TV this is called Multipoint greyscale instead of two point that we do on the Sony Trinitron.Image Removed
We don't have these options in this TV. Because we only 2 Hi and Low and we don't have a control called RGB balance or alike. . . .
Click Next

Color Management System CMS Adjust

Click on Read Series "Goal Post"

Image Removed

On the TV go to the Color Management RED setting Luminance
Click on Infinity button on the calman use the remote to adjust the Luminance, Then Tint, then Saturation.
Try to get the dot in the box.
See pic #7
Red Green Blue get Gamut Luminance to 0 or close by playing with Luminance and Saturation
The Delta controls get them to 0 or close
Delta L = Luminance
Delta C = Chroma
Delta H = Hue
Read the white #'s the Target numbers are what you are trying to get the current readings to match.

OLED New LG – set the backlight for Day Mode
Color Workflow for CMS Primary Colors Red, Green and Blue
Pick Green go to infinity mode
Start adjusting with Luminance
Increase/decrease the luminance
Saturation increase/decrease
Tint increase / decrease
Go back to Luminance
Next Re – Read all 6 Colors again pressing the "Goal Post"
Color Workflow for CMS Secondary Colors Cyan, Magenta, Yellow, White
Pick Cyan go to infinity mode
Start adjusting with Hue or tint
Luminace adjust
Pick Magenta
Start Adjust Tint/hue
Saturation
Then finally Luminance adjust till you get in the hole
Pick Yellow
Start Adjust Tint/hue
Saturation
Then finally Luminance adjust till you get in the hole
Run the "Goal Post" again to see how all the 6 colors are affected
You will usually do two passes

go down to Color Management System
Click on the "Goal Post"
Select the RED Color then Right click on Gamut Luminance area of the image and choose Properties tells us the exact percentage we are off on RED

This shows on the scale how far we are off

If you click on the color of the box as we have clicked on Green then you will get the close up of the offset of the color green dot is out of the box.

Saturation Sweeps to show where the saturation falls