Monitor Calibration - LG OLED 55C7P Calman and Klein Workflow

NOTE you must calibrate the input that the BMD device is connected EX: HDMI 1

You will need the Dell Laptop with the Calman Software installed and the Klien Colorimeter and the Murido signal generator	This is stored in a case in the back of the helpdesk in CMA 3.104
Turn on Monitor so it warms up
Connect Murideo signal generator via USB to laptop. Make sure the Murideo drivers are installed http://www.murideo.com/downloads.html
Plug in the HDMI out of the Murideo Signal Generator output to the TV you want to calibrate MAKE SURE IN USE HDMI 1 WHERE THE BLACKMAGIC I/O IS PLUGGED IN Set the LG TV HDMI input to the input from the Murideo HDMI INPUT 1
Press the red ON button on the Murideo
Now you should see the images from the Murideo on the TV
Murideo Signal Generator connected via USB - Use USB to Serial Port 4 on Laptop for the Murido Signal Generator
On the Klien Camera remove the lens cap
and put on the Lens Hood on the Klien camera
Put the Klien on a tripod Pull up the Murido slide that shows the target as this example *Put the cup smushed up to the TV so rubber is blocking out all the light completely flush to the monitor*
Another example of the camera pressed up against the monitor
Connect the Klein Colorimeter via USB into the computer
Log into laptop	with UN comm - xxxxx and password
Open Calman software on the laptop using the desktop shortcut
Enter in the details and click Start Session Client – Default Calibrator – your name Display System put in as much info as possible (Sony TriMaster ex:) Display Model is PVMX-550 Remember under Workflow choose ISF Calibration Choose Start Session
Hit Next Here
Pick the Resolution 3840 x 2160 24P for the LG Monitors but it should automatically be set from a step before. ??????
Step 1 pick the port com 3,10,11 will change and put a checkbox on the kind of instrument you are using Klein > Search May have to choose different com ports to find the right one
New 004 pic On step 1 make sure you choose OLED or LED or Plasma or Projector etc Suite H Sony choose OLED for example
Click on Step 2 and choose Find Source
Choose Manufacturer - Murideo Model Murideo - Six G com port will have to try different ones but in this case com11 worked
Windows Size This is where you choose the size of the image that the Murideo will be displaying on the screen while calibrating. Recommended to use 18%
This step need to have a TV with a supported Display Control our TV's are not listed AUTO CALIBRATION STEP WE DON'T HAVE If you want to connect the computer to the TV you can hook up the Ethernet or Serial Port and click "Next"
In Calman Software choose Murido 6G Genrator tab Resolution 4096 x 2160 Choose Color Format to be YC444 Leave HDR off Uncheck BT2020
Click on Next
Setup the meter position Remember place the Colorimeter up against the monitor Click Next
On the LG Remote click the Gear Icon and then use the down arrow to get to All Settings
Set the TV to Picture Mode isf Expert (Dark Room)
Turn off the lights in the room put in the CC environment Also put something on the computer monitor "Resolve"
Mode Settings Keep in ISF Dark is as and close to 6500K as possible on this mode setting usually
Now go into each of the Gamma Settings on the Sony or whatever TV Click on >
On the LG Remote click the Gear Icon and then use the down arrow to get to All Settings ISF Dark >Expert Controls> ALL SETTINGS>PICTURE>BRIGHTNESS>GAMMA LEAVE AT BT 1886 GET A PIC ON PHONE ABOUT THIS
To get the mode to be read press>Gamma Preset – Press Read Series or "Goal Post"
to test each of them (2.2, 2.4. 2.6 CRT etc.. .) to find the right one that reads closest to the target line 6500. Good to write these down or can re-name each history tab NEW PICTURE
Here is what the 2 point Gamma reading at should look like See this example Sony was spot on but LG was like this Click on Next
We need to pick out the right Color Temp for the LG TV (1. White Point)
PICTURE OF HOW TO GET TO WHITEBALANCE ON THE LG On the LG Remote click the Gear Icon and then use the down arrow to get to All Settings ISF Dark >Expert Controls > White Balance>to set the color temp
To set the "white point BLOCK" and color space click on the "Infinity button" and while it is running toggle through all the color temp settings that the TV has PICTURE OFF PHONE HERE
PICTURE OFF PHONE HERE with color temperature HIT THE WHITE BOX PIC ON PHONE
cycle through the color temps till the dot is closest to the white point box >Cool
Warm 2 setting is the best the dot is right in the white box
Now we need to set the right Color Space WE THINK COLOR GAMUT ON THE LG'S IS Color Space Check to see if Gamut is set to Auto on the LG's Then click Next Turn off all auto processing
On the LG Remote click the Gear Icon and then use the down arrow to get to All Settings ISF Dark >Expert Controls > Color Management System
Turn off all Auto Features No automatic adjustments should be on Click on Next once all the settings on the TV are off All settings Auto Dynamic is off Video Range Not Auto - Do limited Auto Eye Care Off Peak brightness off Leave Color Gamut to Auto Clarity All off and TruMotion is off Real Cinema Off
Adjust Luminance Click on Read Continuous lower left corner
and adjust the Backlight or on the LG the Contrast setting On the LG Remote click the Gear Icon and then use the down arrow to get to All Settings ISF Dark >Contrast PICUTE HERE
adjust the Backlight setting - Sony TriMaster doesn't have this on the TV our example we set it to max and according to the specs we should be Get the LG to about Contrast at 86 or 30-40 FL	Picture on the phone
30-40 for a dark room these are the specs for the rooms that we want to follow
Next click on the Dynamic Range Click on Brightness button and set so that the Dynamic Range to check this click on Read Series
This is the result of the Read
Not Bad but can adjust Press these buttons Brightness and Contrast Press Brightness button
Press Black Level not Brightness set black level to 58 Press Brightness and will get the controls to adjust for the Black PLUGE test pattern – You want to barely see 16 and 17 but should not see any squares below 16 those should be invisible.
Press Contrast Menu in Calman Software -
to put up the White Pludge you want to see up to 254 and don't want to see any pink tones or noise? Use Adjust Contrast on the LG to adjust this 82 seemed the best
Change the 2.4 to 2.6 and others but 2.4 usually is the best
Gamma Settings control
Press the "Goal Post" again to take a reading of the Gamma Settings
Make sure the White Line is Close to the Yellow Line - less expensive TV's you will see fall off in the Low areas
?????Not sure what we did here notes from other session back in 2017 here We went to lower the Gamma to make it work better Turned on Advanced Contrast Enhancer and LED Dynamic Control Look at the Moving Stripe pattern you want to see the display look darker. This turns on Local Area Dimming
?????Not sure what we did here notes from other session back in 2017 here We ended up turning on Local Area Dimming by turning on LED Dynamic Control Optimizes contrast by adjusting brightness in individual sections of the screen Gamma also was changed to -2 this is a repeat of Gamma on step 2 but this is a 10 point control instead of a 2point control. Click On Next
Color Decoder - Skip this Step on the Sony Trinitron in Grad Suite H
This Sony 65 does not have blue only mode. But click on Color and Tint to see the Color Bars on the Monitor if the TV has that
Turn the "Color and Tint" settings to get these to stripes like this
Click on Next
Resolution/Bit-Accuracy
You can click on the test patterns here
Pull up ISF Geometry to check for OverScan Check for the white lines at the edges to make sure you are seeing everything - Not a crucial step so it's Optional
Click Next!
Greyscale Two Point Adjust

Select 80 Percent White

Click on the 80 percent button

Click on the Continuous read button

You will go to your White Balance settings to find your RGB Gain and Bias
You will control the RED Green and Blue Gain=High controls

You want to adjust the Red Green and Blue controls until you get all 3 RGB colors to match exactly this is close but not exact

This is what we ended up with

Then we clicked on 30 %

Click on the Continuous read button

You want to adjust the Bias controls until you get all 3 RGB adjust the Red Green Blue low or Bias controls colors to match exactly this is close but not exact

Sony you'll use these menus and knobs

This is what we ended up with better all straight

Frame grab of CIE X and Y get a picture to insert here

Toggle back and forth with the 80 and 30 toggle till you get the Bias's and Gains to be absolutely flat

Picture here

Finally after you are finished do a Goal Post "Read Series" to get the final reading to make sure all's good.

Click NEXT

OLED LG has this but we'll skip this on the Sony Trinitron

You can take a "Read Series" click on Goal Post

Object is to get All the Deltas under 5 is exceptable

Get the X to read .312 and the y .to read 329

You would have to adjust the RGB on every point if you have that on your TV this is called Multipoint greyscale instead of two point that we do on the Sony Trinitron.
We don't have these options in this TV. Because we only 2 Hi and Low and we don't have a control called RGB balance or alike. . . .
Click Next

Color Management System CMS Adjust

Click on Read Series "Goal Post"

On the TV go to the Color Management RED setting Luminance
Click on Infinity button on the calman use the remote to adjust the Luminance, Then Tint, then Saturation.
Try to get the dot in the box.
See pic #7
Red Green Blue get Gamut Luminance to 0 or close by playing with Luminance and Saturation
The Delta controls get them to 0 or close
Delta L = Luminance
Delta C = Chroma
Delta H = Hue
Read the white #'s the Target numbers are what you are trying to get the current readings to match.

OLED New LG – set the backlight for Day Mode
Color Workflow for CMS Primary Colors Red, Green and Blue
Pick Green go to infinity mode
Start adjusting with Luminance
Increase/decrease the luminance
Saturation increase/decrease
Tint increase / decrease
Go back to Luminance
Next Re – Read all 6 Colors again pressing the "Goal Post"
Color Workflow for CMS Secondary Colors Cyan, Magenta, Yellow, White
Pick Cyan go to infinity mode
Start adjusting with Hue or tint
Luminace adjust
Pick Magenta
Start Adjust Tint/hue
Saturation
Then finally Luminance adjust till you get in the hole
Pick Yellow
Start Adjust Tint/hue
Saturation
Then finally Luminance adjust till you get in the hole
Run the "Goal Post" again to see how all the 6 colors are affected
You will usually do two passes

go down to Color Management System
Click on the "Goal Post"
Select the RED Color then Right click on Gamut Luminance area of the image and choose Properties tells us the exact percentage we are off on RED

This shows on the scale how far we are off

If you click on the color of the box as we have clicked on Green then you will get the close up of the offset of the color green dot is out of the box.

Saturation Sweeps to show where the saturation falls

Pick a color in the lower left corner to choose white.

Re check the White Levels

You will get the Black Pluge Slide back up and the White Pluge slide back up set these again and set these by eye
Should
Press Brightness and will get the controls to adjust for the Black PLUGE test pattern – You want to barely see 16 and 17 but should not see any squares below 16 those should be invisible

Press Contrast button to put up the White Pludge you want to see up to 254 and don't want to see any pink tones or noise?

Now go to the Sony OLED and lets compare
Go to ETOF and set it to 2.4

ColorChecker Analysis
.4 not visible .6 is visable then you should try to fix it.

Monitor Calibration - LG OLED 55C7P Calman and Klein Workflow

MAKE SURE IN USE HDMI 1 WHERE THE BLACKMAGIC I/O IS PLUGGED IN

New 004 pic

GET A PIC ON PHONE ABOUT THIS

NEW PICTURE

PICTURE OF HOW TO GET TO WHITEBALANCE ON THE LG

HIT THE WHITE BOX

PIC ON PHONE

Picture on the phone

Press Black Level not Brightness set black level to 58

Greyscale Two Point Adjust

Select 80 Percent White