LG OLED Auto-Calibration with Calman- C2 and C6
This is the process for using Calman and the Klein scope to auto-calibrate the LG C2 and C6 OLED televisions.
Before you setup Calman and the Klein scope |
|
|---|---|
It will be easiest if you have the screen you want to auto-calibrate connected to the IOT WiFi. If the screen is not already connected to IOT then consult with Josh to get it set up on IOT. |
|
If you can not get the television connected to IOT you can use a direct ethernet cable connection between the laptop and screen. If you do not know how to do this consult with Moody tech support to set up the laptop and television so they can communicate with one another. |
|
Set up the gear |
|
|---|---|
When you open the case please make note of where different things are stored and how they are packed. You will want to repack it in a like manner. |
|
First you will want to determine if you are going to use the existing HDMI cable that goes from the DeckLink to the LG or if you are going to use a separate HDMI cable. Most of the systems in the Undergrad Suite it will be easier to use the existing cable. Just unplug it from the back of the DeckLink and run it up to the desktop. Most of the systems in the Grad Suites it’s easier to use a separate HDMI. Move the screen away from the wall and unplug the existing HDMI cable. Plug the HDMI you plan to use into HDMI input #1 and run the other end to the desktop. |
|
Next set up the Murideo signal generator.
You will need to connect the power supply, USB cable, and the other end of the HDMI cable to it.
Hold the power button down for a few seconds until the Murideo signal generator begins to power up. |
|
Next turn on the LG TV. It should come up tuned to input HDMI 1. If it is not tuned to input HDMI 1 then change the input to HDMI 1. You should see the output of the Murideo on the LG screen. |
|
Switch the input of the Murideo to one of the Geometry screens. |
|
Next get the Klein scope. Remove the lens cap and screw on the rubber lens hood. Set up the tripod and Klein scope so that the lens hood makes firm and even contact the full circumference of the lens hood with the center of the LG screen.
|
|
Set the laptop on the desk. Connect the laptop power supply, the USB mouse, the Klein scope, and Murideo to the ports as shown.
This should conclude the equipment setup. |
|
Setting up the Calman software before calibrating. |
|
|---|---|
Open the laptop and power it on. Once booted, log in as commpower. |
|
Once the system has finished logging in you will want to launch the Calman software. |
|
Once Calman has finished launching you should see the following screen. Change the Workstation setting to the workstation you are going to calibrate. The Model and Serial Number should update when you do. If the screen has been replaced recently then edit the info for it. |
|
Next, choose the Workflow pulldown menu and choose Calman Ready LG |
|
Then choose Start Session.
It will load the Auto Calibration workflow for LG |
|
Next you will want to connect the Calman software to the LG TV so it can control it. In the upper right select Direct Display panel so it opens up, then choose Find Display. |
|
The Find Display window will open up.
Change the Manufacturer to LG, the Model to match the screen you are calibrating (C2 or C6), and enter the IP address of the LG screen (find that using the LG remote and checking the network settings)
Then click Connect. |
|
If everything works right you a PIN number should get displayed on the LG screen that you need to enter into a box in Calman. |
|
Once Calman has found the LG screen the tab in the top right should change to a green indicator and look similar to this.
All 3 of the tabs at the top should now be green to show that Calman is sucessfully communicating with all 3 devices. The Klein scope, the Murideo, and the LG.
If all 3 are not green then something has gone wrong and you will need to troubleshoot the connections. There is a separate section to cover that.
|
|
Now go to the Klein Tab. Under there make sure it says OLED. |
|
Then under the Murideo tab make sure it’s set to Window 10% Delay 1 3840x2160p 23.976 YC444 10 BIT HDR OFF
|
|
And under the LG tab make sure Display Mode is set to Expert Dark |
|
Start the Auto-Calibration process |
|
|---|---|
Now that everything is connected and communicating correctly you will want to set the Display Type and Mode.
Display Type: OLED Mode: SDR Once done click NEXT to advance to the next page. |
|
Check over the next page to make sure the settings match the image to the right.
Under section 1, below Find Meter make sure it says OLED. Under section 2, below Find Source make sure it says Window Size 10% and Delay 1. Under section 3, make sure the Pattern Insertion is set to: Frequency: 45 Patches: 1 Duration: 5 Duration: 1 Level: 25 Level: 10 Then click NEXT
|
|
On the Targets page you will want to change the Target White and Target Black.
For Expert Dark you will want Target White 100 Target Black 0
The rest of the settings should be correct already, but you can check them against the image to the right.
Then click NEXT
[NOTE: if you are calibrating Expert Bright I recommend that you set the Target White to 300 for the C6 screens and set to 200 for the C2 screens.] |
|
You can just skip past the SDR Current State page. No need for it really. So just click NEXT. |
|
The next page is if you have not yet connected to the LG screen, but I’m sure you have. Haven’t you. But check that it’s set to Expert Dark and rec709, just to be double checking.
Then select NEXT. |
|
Now you should be on the Pre-Cal page. This is where you can take a measurement for a before and after comparison. So you could skip this if you like, but I usually do it.
One thing I prefer to do is to set the system to include black in the auto-cal adjustments.
You can click on the gear icon in the upper right and then select the Advanced Options. Then check the Include black in AutoCal adjustments.
Also double check that the Black Target is set to 0 and the White Target is set to 100. |
|
Once you are ready click on Measure.
The system will take a measurement of the current display settings that it will save and use later when making a before/after report. It takes about 8min usually.
Once done click NEXT. |
|
Now you should be on the Reset page. Make sure it still says SDR Expert Dark and then select Reset. This will clear out any 1D and 3D LUTs that may be in the Expert Dark setting and get you back to a starting point for calibration.
NOTE: This may take a minute to two. The green bar on the LG tab in the upper right should be blinking white after you click Reset. Wait for the blinking to stop and the bar on the tab to become green again before clicking NEXT. |
|
The next page is the initial luminance adjustment. Our target for the Expert Dark setting is 100. Which you would have set earlier, and should now be listed as the Target Luminance on this page. When you select AutoCal is will think for a few seconds and then ask you to confirm that you want to target a luminance of 115, which you WANT TO DO. You want to allow for a 15% overage here, and this panel takes that into consideration. So leave the setting at 115 and click OK. It will take a minute for it to finish the process and once done you are ready to click NEXT.
NOTE: if you are calibrating Expert Bright for 200 or 300 then it will calculate for the 15% overage here based on that. |
|
Now we are on the Greyscale-Multipoint calibration page. This is where it sets the gamma and white balance across the greyscale.
Once you select AutoCal a window will pop up. You will want to make sure to change the drop down for Active Greyscale Points over to Detailed 16-255 (Extended). And then click OK.
This part of the AutoCal will take about 15min. Afterwards CalMan will build a 1D LUT and upload it to the LG TV.
Once complete click on NEXT.
|
|
Now we are on the 3D LUT Calibration page. CalMan will sample a wide range of colors with the purpose of building a 3D LUT that will bring wide range of the colors of the gamut into their correct placement. After you click on AutoCal a window will open.
Make sure you change the Calibration Type to Fixed Grid 9 Point. Then select OK.
This will take about 45min to complete. Once done CalMan will build a 3D LUT and upload it to the LG TV. Once done you can select NEXT. |
|
You should now be looking at the Verify Luminance page. This is where you will have CalMan adjust the final luminance to your target value. Click on AutoCal.
A new window should pop up. Make sure you target is correctly set, for Expert Dark it should be 100. Then click OK.
This will run for a minute and should correctly set the luminance on the LG TV. Once done select NEXT. |
|
The End Calibration is where you tell CalMan to stop making adjustments to the LG TV.
Click on the check mark and wait for CalMan to close the calibration process.
Once done you can select NEXT. |
|
This next page, the SDR Post-Cal page, is where CalMan will take a series of measurements that it will use in the before/after report.
Select Measure and let it do it’s thing.
This will take about 9min.
Once done select NEXT. |
|
On this next page you will click on Save & Report.
A window will pop up where you select Save Calibration Session with Specific Name. |
|
Yet another page will build and display. It’s been a LOT of pages. Whew. But this is the FINAL PAGE!!!! (sort of) Click on Save to PDF. A Windows window will open. Navigate to where you want to save the PDF of the calibration session. I usually change the name to something like CMB-4120-4_2026-10-28_AutoCal_ExpertDark_100nit That way I know what workstation this calibration report is for, the date it was done, if it was manual or autocal, the TV setting that was calibrated, and the target luminance that was choosen. (pretty cool, right?) |
|
The final thing is to put all the gear away carefully in the manner that you found it. And make sure that the LG TV is connected correctly to the DeckLink. And that the LG TV is set to HDMI 1 Input. |
|