Frame Tabs Info Sheet
please make sure your tabs are in the 24-BDY-1100 (Frame Assembly).SLDASM file. even if you think they're on the frame, please double check and add below the following info:
system
part
needs validation? (does it need to be verified that it can carry the load of whatever part will be mounting to that location)
needs jigging? (does the part need to be precisely welded onto exactly a specific location on the frame, or is a little bit of error okay so long as the tabs are accurate relative to each other)
needs welding? - do we (frame) need to weld those tabs, or is there an alternate mode of attachment?
if you can manufacture the tab on your own (waterjet/lasercut)
System | Part | Needs Validation? | Needs Jigging? | Jig Completion | Welded? | Manufac on your own? | Ordered? | General Location |
|---|---|---|---|---|---|---|---|---|
Powertrain | PDE Top | NO | Enclosure-Human Jig | YES |
| YES | YES | Rear Roll Hoop |
Powertrain | 2x PDE Diagonal | NO | Enclosure-Human Jig | YES |
| YES | YES | Rear Roll Hoop |
Powertrain | 4x Battery | YES | YES | YES | YES | YES | YES | Battery Chamber |
Powertrain | 2x Telemetry Diagonals | NO | YES | YES |
| YES | YES (SCS Batch 2) | Rear Roll Hoop |
Powertrain | 1x Telemetry Top Tab | NO | YES | YES |
| YES | YES (SCS Batch 2) |
|
Powertrain | 2x Pump | NO | YES | YES | YES | YES | YES | Left hand side, top longitudinal tube of battery chamber |
Powertrain | 1x Radiator | NO | YES | YES | YES | YES | YES | Right hand side, top longitudinal tube of battery chamber |
Powertrain | 1x Moco Right side | NO | YES |
|
| YES | YES |
|
Powertrain | 1x Moco left side | NO | YES |
|
| YES | YES | Top longitudinal tubes of battery chamber |
Powertrain | 1x Moco Rear | NO | YES |
|
| YES | YES | Rearmost Lateral Frame Tube |
Powertrain | 2x Fusebox | NO | YES | YES | YES | YES | YES | Left Roll Hoop |
Aerodynamics | 2x Lanyards | YES (Advait is doing this) | NO |
|
| YES |
| one on front and one on back of frame (very descriptive) |
Aerodynamics | 4x Top Shell to Frame | NO | YES |
|
| NO |
| top level tubes |
Aerodynamics | 4x Tilting Mechanism | NO | YES |
|
| NO |
| top level tubes |
Aerodynamics | 1x Canopy Latch | NO | NO |
|
| NO |
| top level tubes |
Aerodynamcs | 3x Anti Droop | NO | NO |
|
| NO |
| front and back top level |
Ergo | 2x Common Ballast | NO | YES (for tabs relative to each other) | YES | YES | NO | YES | Front of frame |
Ergo | Inidividual Ballast | NO | YES | YES | YES | YES | YES | Behind seat of driver near right side |
Ergo | 4x Pedal Box | NO | YES (for relative position) |
| YES | NO | YES | 2 on each side, pedal box |
Ergo | 6x Seatbelt | YES | NO |
| YES | NO | YES | 2 under driver’s legs, 2 next to driver on floor tubes, 2 behind driver near the top |
Ergo | 4x Seat Back | YES | YES |
| YES | YES | YES | 2 next to driver on floor tubes, 2 next to driver on top-level tubes |
Ergo | 4x Dashboard | NO | YES |
|
|
| Yes (SCS Batch 2?) | Dash Tube |
Composites | 4x Egress | YES | YES | YES | NO | NO | NO | Left of driver |
Dynamics | 2x Shock | YES | YES |
|
|
|
| 1 on each side, top level tubes |
Dynamics | 2x Bellcrank | YES | YES |
|
|
|
| 1 on each side, between midlevel ca tabs |
Dynamics | 8x Control Arm | YES | YES |
|
|
|
| 4 on each side, 2 midlevel, 2 bottom level |
Dynamics | 2x T Arm | YES | YES |
|
|
|
| Rear, mid level, one straight, one angled |
Dynamics | 1x Rear Shock | YES | YES |
|
|
|
| Rear, top level, above straight T arm tab |
Dynamics (Steering) | 2x Steering Rack Plate | NO | YES |
|
|
|
| 2 plates on bottom tubes in front of pedal box |
Dynamics (Steering) | 2x Bearing Housings | YES | YES | In progress |
| YES |
| 2 cylinders welded to diagonal tubes near dash |