Nextbreak Manafacturing
System | Part | Where in Bild | Material | Have stock (Y/N) | When needed by | Quantity | Notes |
|---|---|---|---|---|---|---|---|
Body | Pucks | 24-BDY-1400 (Aluminum Pucks) | Aluminum 6061 | N (Ordering soon) | 11/24 | 52 | Body can probably manufacture, we just need supervision for the first couple of times |
Body | L Brackets | DL-2313N39-McMaster (Aluminum Corner Machine Bracket 2in x 1.75in) | Aluminum 6061 | N | 11/24? | TBD | Face down and then holes, all same hole location |
Body | T-Slot | DL-47065T103-McMaster (TSlot 1.5x1.5x20) DL-47065T418-McMaster (T-Slotted Framing 2in x 1in) | Aluminum? | Y | 11/24 | 8 | Stock is in the garage just need to trim down to the dimensions we need and ensure top and bottom are flat |
Steering | Rack Extender
| 24-DYN-3104 (Rack Extender) | 6061-T6 | Y | 11/24? | 2 | Stock is on SPurM need to drill hole for bolt and then bore out hole for shaft |
Steering | Pillow Block | 24-DYN-3101 (Steering Rack Clevis) | 6061-T6 | Y | 11/24? | 2 | Stock is on SPurM, need to mill to spec and then drill bolt holes |
Steering | Steel Inserts | 24-DYN-3307 (Upper Tube Steel Insert) 24-DYN-3308 (Steel Pinion Insert) | 4130N | Y | 11/24? | 1
1 | Stock is on SPurM, need to lathe down and then drill and bore the ID |
Steering | Upper Steering Shafts | 24-DYN-3311 (Aluminum Steering Shafts) [Upper Shaft and Lower Shaft Config] | 6061-T6 | Y | 11/24? | 1 1 | Stock is on SPurM, just need to bore out inside to fit with inserts |
Steering | Upper Steering Bushing Housing | 24-DYN-3304 (CF Upper Steering Shaft Bearing Housing) | 4130N | Y | 11/24? | 1 | Stock is on SPurM, just need to bore out for bushing and shaft and then lathe OD to meet dimensions |
Steering | Al Inserts | 24-DYN-3306 (Aluminum Insert) | 6061-T6 | Y | 11/24? | 2 | Stock is on SPurM, need to lathe down and then drill and bore the ID |
Steering | Al Middle Shaft | 24-DYN-3303 (Middle Al 7075 Steering Shaft Stepdown) | 6061-T6 | Y | 11/24? | 1 | Stock is on SPurM Need to lathe down OD and lathe stepdown and then drill and bore out ID |
Steering | Upper Steering Bearing Housing | 24-DYN-3305 (Al Middle Shaft Bearing Housing) | 4130N | Y | 11/24? | 1 | Stock is on SPurM Lathe down OD and then mill out shoulder and ret ring groves |
Steering | Al Tie Rods | 24-DYN-3211 (Rod) [Al Tie Rod Config] | 6061-T6 | Y | 11/24? | 2 | Stock is on SPurM Insert helicoil and lathe down OD |
Steering | Torsion Jig Hex Head Brace | 24-DYN-3313 (Bushing Housing) | 6061-T6 | Y | 11/24? | 1 | Stock is in Solar Cabinet Mill and then drill holes |